May 28, 2022

Do you know you may make a struggle hammer with a number of metallic rods and the instruments you have already got in your shed? Study with us on this information on learn how to make a low-budget however purposeful struggle hammer.

RELATED: DIY Survival: How To Make A Crossbow From Scratch [Video]

Making a Conflict Hammer in Six Easy Steps

Issues You’ll Want:

  • A flat metal bar (1½ x ¼ x 36) inch
  • Zinc plated flat metal bar with holes (1 3/8 x 1/16 x 36) inch
  • An angle iron (1 ¼ x 1/8 x 36) inch
  • 14 units of three/8-inch nuts, bolts washers, and lock washers
  • 1/4 -inch wooden or board
  • Paracord

Instruments You’ll Want:

  • A 3/8-inch drill bit
  • An angle grinder with a grinding wheel and a cut-off wheel and
  • A drill
  • Vise
  • C Clamp
  • Ratchet

Step 1. Mark Out the Metal Bars

Firstly, use a sharpie to attract large strains at each 5 inches on the skin of the angle iron. The road ought to cowl either side of the angle iron. Right here it’s best to have 4 five-inch sections.

Subsequent, measure two inches in from the nook after which drop a diagonal line. Do that on either side of the primary two five-inch sections.

My-Rights-Dont-End-ad

On the third five-inch part, measure two inches from the nook and solely drop a diagonal on one facet. Do the identical on the final five-inch crew however on the alternating facet.

Secondly, mark out a 2 ½ inches part on the flat bar. Subsequent, measure out one other four-inch and mark it out. Subsequent, from the border of the 2 areas, measure two inches into the four-inch part and drop a diagonal.

See also  How to Build Bomb Shelter | 15 Steps on How to Build a Bomb Shelter

Step 2. Lower the Marked-Out Bars

Check out How To Make A War Hammer at https://survivallife.com/war-hammer/

Now, use an angle grinder with a cut-off wheel to chop the angle iron and the flat bar to dimension. It can save you the items of metal you’ll not use for one more challenge.

Subsequent, use the identical angle grinder to chop off the top of the zinc-plated metal bar with a half gap to match the opposite straight finish. Now, use your sharpie to mark 4 sections on the zinc-plated bar.

The primary three ought to have seven holes every, whereas the final one ought to have 13 holes. Use the grinder to chop the zinc-plated bar to dimension.

Tip: If you’re not utilizing a bar with holes, measure out 5 ¼ inches for 3 small sections and 9 ¾ inches for the extra intensive part.

Step 3. Bend the Zinc Plated Items to Type Brackets

Check out How To Make A War Hammer at https://survivallife.com/war-hammer/

Right here, take a bit of your ¼ -inch flat bar, align it with the middle gap on one in all your zinc plated flat punch. Subsequent, clamp it onto your vise and bend the higher a part of your zinc plated bar over the flat bar as tightly as you’ll be able to.

You should utilize a blacksmith’s or common hammer for this. For this step, use two of the three smaller items of the zinc-plated bar.

Do the identical for the remaining zinc-plated punch items. The one distinction right here is that you’re going to bend them over two stacked flat bars. For this, use a tape measure to mark out a 22 ½ -inch after which reduce it utilizing a grinder.

Be aware: Stack your 22 ½ -inch flat bar with some other bar for the second layer of brackets. It doesn’t must be the identical size.

RELATED: How To Make A Spear | DIY Survival Spear

Step 4. Bracket the Hammerhead Components

Check out How To Make A War Hammer at https://survivallife.com/war-hammer/

Firstly, take two angle iron items with totally different edges (one with two diagonal strains and one other with one diagonal line. Align them on a flat floor such that the straight edges match.

See also  How to Survive a Nuclear War: 10 Ways to Stay Alive

Subsequent, take one of many small brackets and slide it onto the aligned iron items. Do that from the straight edge and slide it as far down as it might probably go.

Now, tightly clamp the alternative edge on the vise after which use a C clamp to carry the bracket in place as you utilize a hammer to slip the bracket additional down. There must be no area left between the bracket and the angle bars. Repeat this step for the remaining set of angle iron rods and one of many smaller brackets.

As soon as completed, clamp the bracketed angle iron bars with a C clamp to maintain the whole lot in place. Subsequent, clip the iron bars onto the vise. Afterward, take away the C clamp and use a drill to make holes on the bracketed angle bars.

That is easy as you’ll solely have to undergo a gap on one facet of the bracket and drill till you come out by means of the bracket gap on the alternative facet. As soon as completed, insert a bolt, washer, lock washer, and tighten the nut with a ratchet.

Subsequent, flip the hammerhead half and do the identical for the third punch gap. After drilling a gap and tightening the nut, it’s best to have one undrilled gap within the center. Repeat this with the opposite bracketed set of angle iron bars.

Step 5. Assemble the Hammerhead

Check out How To Make A War Hammer at https://survivallife.com/war-hammer/

Now align the 2 units of bracketed angle iron bars such that they’re symmetrical with one another. This fashion, you’ll find yourself with one straight edge with no diagonal reduce on the facet of the hammerhead.

To this edge, slide on the big zinc-plated bracket. Subsequent, slide the remaining small bracket on the opposite fringe of the hammerhead. Slide it from the straight finish. Remember that these two brackets could have loose-fitting.

Subsequent, flip the hammerhead and suit your 2 ½ -inch spacer between the 2 angled items of the hammerhead. You should utilize one other metallic to push the spacer to position. As soon as the spacer is in place, the 2 brackets will now match snugly.

See also  How To Make A Perimeter Alarm

Now drill extra holes onto the 2 new brackets and tighten your bolts. Be sure that your two new bolts don’t intrude along with your beforehand added bolts.

Step 6. Connect the Steel Deal with and the Punching Spike

Check out How To Make A War Hammer at https://survivallife.com/war-hammer/

As soon as the hammerhead is assembled, slide the 22 ½ – inch flat rod by means of the area between the 2 angled components of the pinnacle. Be sure that it’s firmly pressed in opposition to the primary spacer you inserted. When in place, drill two extra holes and insert the bolts to carry them in place.

Subsequent, slide the armor punching spike onto the again of the hammerhead and drill in two holes for the 2 bolts that can hold it in place. Lastly, screw on the deal with and wrap it with a paracord for comfy dealing with.

Be aware: When you determine to color your struggle hammer, take the hammerhead aside, paint the whole lot besides the brackets and bolts, after which reassemble it.

Watch this video by ZNA Productions on learn how to make: the struggle hammer:

There you have got it, preppers. With this easy illustration, you make simply make a struggle hammer at dwelling. What’s extra, it doesn’t require a lot, and subsequently you’ll not must lay our a fortune to personal one. Get inventive and customise yours to your wants and style.

Loading ... Loading …

The place will you utilize your struggle hammer? Tell us within the remark part under! 

Up Subsequent:

Calling all preppers, craftsmen, bushmasters, outdoorsmen, and all-around expert individuals, Survival Life wants YOU! Click on right here if you wish to write for us.

Don’t neglect to remain linked with us on Fb, Twitter, Pinterest, and Instagram!